Repairs due to fire damage: 1 story freezer. Remove fire damaged wall panel east side. Replace with new.

Install 400amp feed to panel, 2 - 200amp feeds to 2 compressors and 1 - 30amp feed for air dryer

Removal and replacement same as existing hvac unit that serves the main office area. The new rtu is one york 12. 5 ton ,r410a, self contained, two compressors, located on the roof.

Extend 100a feed for roof top air conditioner replacing existing.

Relocate the fireman's dump station.

Tear-off and roof replacement using a sarnafil 60 mil f. A. Roofing system. There are four areas which include office and storage area.

3124 sf tanker unloading building addition and electrical room addition as per plan

Updated power and control for glycol system. New amonia detection system.

Replace existing roof membrane (no structural work, no mep work)- all work same as existing; subject to field inspections

New chilled water loop system to replace amonia. Amonia detection system to monitor remaining cooling equipment.

Replace existing 2500a 120 240v 3p3w main service switchboard with new main breaker 2500amp switchboard. Disconnect and remove 2nd 3000amp service switchboard and refeed branch from new 2500amp service switchboard.

Replacement of existing roof membrane with new insulated puc membrane. Same work as exixting. No structural work.

Install one (1) 30a 240v circuit 3 phase for cip process skid. Install one (1) 20a 240v 3 phase circuit for return pump. Install one (1) 20a 120v circuit for sanitizing system. Install associated control wiring.

Extend refrigerant relief line above catwalk. Replace three sight glasses. Replace 26 relief valves 16-hydrostatic, 10-atmospheric.

1. 0) furnish & install one (1) 20hp 240v feeder from existing 240v allen bradley mcc to new vfd location within mcc to facilitate field located tank seperation pump; installation shall include rigid steel conduit within mcc rrom, hardware, wiring, 50a 2100 series feeder bucket, install allenbradley power flex 70 vfd furnished by otehrs, & wiring terminations2. 0) mount one (1) customer provided control panel adjascent to mcc on unistrut floor stand rack within mcc room. Installation shall includ

Tear off and replace roof

Install 400amp feed to panel, 2 - 200amp feeds to 2 compressors and 1 - 30amp feed for air dryer

Extend 100a feed for roof top air conditioner replacing existing.

Relocate the firemans dump station.

New chilled water loop system to replace amonia. Amonia detection system to monitor remaining cooling equipment.

Replace existing 2500a 120 240v 3p3w main service switchboard with new main breaker 2500amp switchboard. Disconnect and remove 2nd 3000amp service switchboard and refeed branch from new 2500amp service switchboard.

Tear-off and roof replacement using a sarnafil mil f. A. Roofing system. There are four areas which include office and storage area.

Replace existing roof membrane (no structural work, no mep work)- all work same as existing; subject to field inspections

Addition of a 1-story industrial building to an existing manufacturing building for nestle-beverage processing area as per plans.

Repairs due to fire damage: 1 story freezer. Remove fire damaged wall panel east side. Replace with new.

Tear off and replace roof

Install one (1) 30a 240v circuit 3 phase for cip process skid. Install one (1) 20a 240v 3 phase circuit for return pump. Install one (1) 20a 120v circuit for sanitizing system. Install associated control wiring.

Interior alterations at 1st floor for per plans.

Low voltage fire alarm conduit and wiring to facilitate capital non-required fire alarm devices on existing system.

Removal and replacement same as existing hvac unit that serves the main office area. The new rtu is one york 12. 5 ton ,r410a, self contained, two compressors, located on the roof.

Furnish and install motor power, control, instrumentation wiring from existing panel ha to field located drive and control panels a, b, c, d, e, f. Clarifier, briddo mixer flexicon conveyor admix and filler and conveyor equipment.

Replacement of existing roof membrane with new insulated puc membrane. Same work as exixting. No structural work.

1. 0) furnish & install one (1) 20hp 240v feeder from existing 240v allen bradley mcc to new vfd location within mcc to facilitate field located tank seperation pump; installation shall include rigid steel conduit within mcc rrom, hardware, wiring, 50a 21 series feeder bucket, install allen? Bradley power flex vfd furnished by otehrs, & wiring terminations2. 0) mount one (1) customer provided control panel adjascent to mcc on unistrut floor stand rack within mcc room. Installation shall include all galvanized unistrut, zinc hardware, and labor to mount. 3. 0) furnish & install one (1) dedicated 3? Phase 240v power dedicated pump feed from the new vfd unit located within mcc room, to the field located pump unit; installation shall include pvc coated rigid steel conduit to the field, hardware, wiring, & wiring terminations

Install low voltage equipment on roof

Tear down and remove brick chimney stack

Remove existing suspended ceiling tiles, grid, light, fixtures, wall ac units, abandon ductwork, original lath plaster ceilings and 11 interior doors, roof penetrations, no structural work. Electrical to be pulled under seperate permit

Electrical demolition in conjunction with building permit #100732650

Remove and replace 12 ammonia evapoators with 12 fan coil units, install 2 ammonia to glycol heat exchangers and all associated piping as per stamped plans. Contact bob o'mara at 312-743-7215 for testing of ammonia piping.

Updated power and control for glycol system. New amonia detection system.

Interior build-out for new quality assurance laboratories. Build-out is 970 square feet to an existing beverage factory.

Interior buildout for an air compressor room and a chemical storage room for sanitation supplies and renovation of a drum sampling room to inspect product. These three rooms are located within the existing warehouse. Size of rooms are: air compressor room=925 square feet, chemical storare room=321 square feet and drum sampling room =120 square feet.